| HUB CITY FB110UR X 1-1/4S Flange Block Bearings | Oil Speed Rating n2:9000 rpm; B:23.00 mm; D:90.0000 mm; Grease Speed Rating n1:6700 rpm; Fillet Radius ra:1.50 mm; d:40.000 mm; Basic Dynamic Radial Load Rating C:47500 N; Basic Static Radial Load Rating Co:30500 N; |
| HUB CITY FB250HW X 1 Flange Block Bearings | D:130.0000 mm; d:75.000 mm; Basic Static Radial Load Rating Co:72000 N; Fillet Radius ra:1.50 mm; B:25.00 mm; Accessories:One Shield & Snap-Ri; Oil Speed Rating Open/Shielded n2:4800 rpm; Basic Dynamic Radial Load Rating C:74800 N; Grease Speed Rating Open/Shielded n1:3900 rpm; |
| HUB CITY WSTU250 X 1-3/16 Take Up Unit Bearings | h:295 mm; Basic static load rating C0:585 kN; Basic dynamic load rating C:400 kN; l2 max.:389 mm; C1 max.:48 mm; d2 max.:182 mm; Specific dynamic load factor K:100 N/mm²; Material constant KM:330; l7 min.:98 mm; B:55 mm; |
| HUB CITY FB250DRW X 1-1/4S Flange Block Bearings | r2s (min):0.6 mm; Pu:35.800 kN; rs (min):2 mm; d2:80 mm; a:31 mm; B:37 mm; T:37 mm; Static (Coa):300 kN; D:130 mm; C:29 mm; |
| HUB CITY B250R X 1-5/8 Mounted Units & Inserts | Limiting speed:53000 r/min; r1,2 min.:0.15 mm; D3:15 mm; da min.:7.2 mm; Fatigue load limit Pu:0.01 kN; D2 ≈:11.7 mm; da max.:7.3 mm; Basic dynamic load rating C:0.618 kN; d:6 mm; Reference speed:110000 r/min; |
| HUB CITY FB350H X 1-1/2 Flange Block Bearings | da:100 mm; Taconite seal (dc shaft position):TER 106; Cap bolt:5/8-11 UNC; Max. speed for Taconite seal:675 r/min; H2:44.45 mm; Initial grease fill:365.71 g; Ca:55.804 mm; Stabilizing ring:SR-20-17; Lock nut:AN 20; H:222.25 mm; |
| HUB CITY FB250STW X 1-3/4 Flange Block Bearings | Calculation factor f2C:1.06; Mass bearing:1.2 kg; D:140 mm; Number of balls z:28; Reference grease quantity Gref:14 cm³; Calculation factor f2B:1.03; Calculation factor fHC:1; Basic dynamic load rating C:33.8 kN; r1,2 min.:1.5 mm; B:24 mm; |
| 0.875 Inch | 22.225 Millimeter x 1.217 Inch | 30.9 Millimeter x 1.313 Inch | 33.35 Millimeter HUB CITY PB220UR X 7/8 Pillow Block Bearings | Specific static load factor K0:45 N/mm²; B:120 mm; Tolerance housing:H7; Coefficient of friction µ min.:0.08; Coefficient of friction µ max.:0.15; Tolerance shaft:e7; α:124 °; Mass bushing:6.97 kg; Specific dynamic load factor K:25 N/mm²; a:6 mm; Size (mm):0.875 Inch | 22.225 Millimeter x 1.217 Inch | 30.9 Millimeter x 1.313 Inch | 33.35 Millimeter ; |
| HUB CITY TU220 X 5/8 Take Up Unit Bearings | PosiTrac Plus contact element:2 x B10724-188; Housing:SSAFS 518; R1:60.325 mm; da:79.375 mm; A2:149.225 mm; Pa:10.9 kN; Bearing:22218 EK; P90°:84.5 kN; H1:101.6 mm; S:4.763 mm; |
| HUB CITY FB250N X 2 Flange Block Bearings | F:25 mm; d:20 mm; Mass inner ring:0.04 kg; B:30 mm; r, r1,2 min.:0.3 mm; |
| HUB CITY WSTU250 X 1-1/4S Take Up Unit Bearings | Basic Interchange MCGILL:-; Basic Interchange:-; Basic Interchange NDH:-; Basic Interchange BCA:-; Accessories:Mast Guide Type- 311; Basic Interchange SPLIT:-; Basic Radial Load Rating-Static SCO:73100 lbf; Basic Radial Load Rating-Dynamic DC:16400 lbf; Basic Interchange NSK:-; |
| HUB CITY TU250N X 1-1/4 Take Up Unit Bearings | d:15.000 mm; B:11.00 mm; Oil Speed Rating n2:26000 rpm; D:35.0000 mm; Fillet Radius ra:0.64 mm; Basic Dynamic Radial Load Rating C:8060 N; Grease Speed Rating n1:20000 rpm; Basic Static Radial Load Rating Co:4750 N; |
| 0.75 Inch | 19.05 Millimeter x 0.984 Inch | 25 Millimeter x 1.25 Inch | 31.75 Millimeter HUB CITY PB250UR X 3/4 Pillow Block Bearings | d:25.000 mm; Oil Speed Rating Open/Shielded n2:18000 rpm; Basic Dynamic Radial Load Rating C:11200 N; Fillet Radius ra:0.64 mm; Sealed Speed Rating n3:9500 rpm; Basic Static Radial Load Rating Co:6550 N; Accessories:Two Seals & Snap-Rin; B:12.00 mm; D:47.0000 mm; Grease Speed Rating Open/Shielded n1:15000 rpm; Size (mm):0.75 Inch | 19.05 Millimeter x 0.984 Inch | 25 Millimeter x 1.25 Inch | 31.75 Millimeter ; |
| HUB CITY TPB220UR X 1-7/8 Mounted Units & Inserts | Design (sliding contact surface combination):Steel/steel, heavy-d; C:22 mm; Basic static load rating C0:500 kN; r2 min.:1 mm; Da max.:57.8 mm; Specific dynamic load factor K:100 N/mm²; dk:53 mm; da min.:44 mm; Material constant KM:330; d1 ≈:45 mm; |